UBERTI SAA 1P AGED STAG GRIPS ~ Cattleman, Evil Roy, El Patron, Pistoleer, etc.

Description: Arizona Custom GripsUBERTI SAA(SINGLE ACTION ARMY REVOLVERS)~ Exclusive ~ MAGNA-TUSK™Aged STAG GRIPSSimulated Stag milled out of a solid block of Magna-Tusk, denser and heavier than regular Ivory or Stag. See below for details.~~~~~oNE-PIECE (nO SCREWHOLE) STYLETHIS AUCTION IS FOR OUR ONE-PIECE (NO SCREWHOLE) STYLE GRIPS. SEE BELOW.********Note: Two-Piece grips, in addition to a visible screw, have a grip pin installed in the frame to help hold them in place. One-Piece grips (grips with no visible screw) use a spacer between the panels, with no screw and no grip pin. BOTH styles of our grips will interchange and work on either style of grip frame. See below. One-Piece style grips (i.e., grips which do not have a visible screwhole in the grips) incorporate a user installed spacer between the grip panels, as seen on many of the early Colts. This results in a rock-tight fit, without the need of a screw. Preferred by many collectors for their clean lines and traditional look, One-Piece style grips are removed by removing the three backstrap screws, and pulling the grip and strap backwards. Reinstallation is in reverse order. Our One-Piece grips will work on either style gripframe (either One-Piece or Two-Piece style grip frames). Fully illustrated instructions included for quick and easy installation.Alternatively, our Two-Piece style grips (i.e., grips with a visible screw) offer the superior convenience of quick grip removal. Unlike with One-Piece grips, the backstrap need not be removed to remove the grips for cleaning and maintenance of the revolver. Our Two-Piece grips include a free Conversion kit (allowing their use on One-Piece style frames) which replaces the need for a grip pin and is actually a stronger design, and allows the grips to lock up tight, allowing no movement. This requires no modification to your revolver and gives you the advantage of the ease of maintenance of Two-Piece grips, while preserving the integrity of your revolver in original factory condition. Two-Piece style grips were also used on many of the early Colts, and are a traditional and iconic historical design, offering a distinctive look and convenience preferred by many collectors.Fully illustrated, detailed instructions are included with each set of grips. 22010345~~~~~WHAT THESE WILL and WILL NOT FIT – Please read this section in its entirety to ensure you get the correct grip: This auction is for a set of Genuine Magna-Tusk™ grips for any of the UBERTI made 1873 SAA (Single Action Army) style revolvers, with the standard sized (around 3-1/6” to 3-1/8” tall) “plowhandle” style grip frames ONLY. [Please note that these will NOT fit the taller 3-3/8” 1860 Army sized gripframes – see below].These will be marked “Uberti,” and may also (but not necessarily be) marked by the U.S. importer, such as “Cimarron,” “Taylors & Co.”, “Navy Arms”, “Stoeger”, “EMF”, etc. The important thing to determine is that the revolver was made by the Uberti factory and not by some other maker. If you see your revolver listed below, then these grips WILL FIT (subject to the few exceptions noted below). These grips will fit any of the following Uberti-made revolvers with the standard sized “plowhandle” style gripframe: ● Cimarron Uberti revolvers: Buntline; Cattleman; Cattleman II; Chisholm; Desperado; El Patron; Evil Roy; Frisco; Holy Smoker; Hombre; Horseman; Cimarron Model P and Model P Jr.; New Sheriff; Old West; Pistoleer (NOT the Pistolero); Rooster Shooter; Short Stroke CMS Pro; Short Stroke SASS Pro; Stallion; Thunderstorm and Thunderstorm CM; US Military Models (Custer 7th Cavalry, U.S. Cavalry Scout, and U.S.V. Artillery); Wyatt Earp Buntline, and Wyatt Earp Cody; ● Taylor’s & Co. Uberti revolvers: Cattleman (NOTE: will NOT fit the Cattleman .44 Mag – see below); Cattleman 12-Shot; Devil Anse; Drifter; Gambler; Old Randall; Outlaw Legacy; Ranch Hand; Runnin’ Iron; Smoke Wagon; Stallion .22, Taylor Gambler; and Taylor Marshall. (Note: will NOT fit the Taylor’s Gunfighter or Gunfighter Defender – see below);● Also: Will also fit any of Stoeger’s Uberti revolvers; the E.M.F. Dakota II or Dakota III; the American Arms Regulator; or any other Uberti SAA style revolver with the standard sized (3-1/6” to 3-1/8”) plowhandle grip frame.Note: If you do not see your pistol listed, please drop us an email with your model name and we will verify your revolver. BRASS GRIP FRAMES -- IMPORTANT!*PLEASE NOTE: Uberti has used multiple variations of gripframes over the years on their SAA style revolvers, both in Steel and Brass. If you have a BRASS gripframe, please send us an immediate followup email after your purchase informing us that 1) your revolver has a brass gripframe, and 2) please send us the two-letter or two-number code found in the small rectangular box stamped underneath or on the side of the receiver (or occasionally under the barrel). This is shown in the second photo as an example. We will need this code to make sure you get the correct grips. If we do not receive the code from you, we will send out the latest version. What these WILL NOT FIT: 1. Please note that these grips will NOT fit other makes of revolvers, such as revolvers made by Pietta, Armi San Marco, Colt, Ruger, etc. Also, please note that these grips are made to fit the “Plowhandle” shaped gripframes only; these grips will NOT fit the non-plowhandle shaped gripframes, such as the Bisley, the Birdshead, the Thunderer or the Lightning style gripframes, which use a completely different shaped grip. We make grips for all of these which you can find in our store, so please email if you have any questions or cannot find what you need.2. ALSO PLEASE NOTE, as a reminder, these grips are made for STANDARD SIZED grip frames ONLY and WILL NOT FIT any larger (taller) 1860 Army sized grip frames. Please check your grip frame measurement prior to ordering. Your grips or grip frame should measure somewhere between 3-1/16 – 3-1/8” tall, depending on how you hold your ruler, tape, or caliper. Some revolvers use a taller 3-3/8” 1860 Army sized grip. Taylor & Co.’s Gunfighter or Gunfighter Defender, Taylor’s Cattleman 44 Mag., Cimarron’s Bad Boy, the El Patron Grizzly Paw, and the Uberti Callahan, for example, have a taller 3-3/8” grip frame. If you have one of these, our Uberti 1860 Army Conversion & Metallic Cartridge revolver grips are made and fitted for these revolvers. Please see our store and search under the proper category or email if you cannot find what you need.Please contact us if you cannot find what you need, or if you have any questions. We are always happy to help.12122100A note on the Italian-produced Revolvers: The Italian firms, located in Northern Italy, have been making SAA style revolvers now for well over a half century, and have made a huge number of makes and models and grip frame profiles with varying configurations over the years. We have an in-depth knowledge of the differing grip configurations, have a large library of gripframe variations from the various makers both old and new, and have vast experience making grips for Uberti, Pietta, Armi San Marco, and the other Italian gunmaking firms. Our experienced makers go to great lengths to ensure an exacting fit, including utilizing modern precision CNC production techniques, as well as incorporating old-time hand tuning and hand checking the fit of every grip on our reference frames prior to leaving our factory. We have a long list of many satisfied customers in the shooting industry who have purchased grips to use in a wide variety of applications, and we can safely and confidently guarantee proper fit and finish to your complete satisfaction.For an additional charge, custom fitting is an option. Please contact us for further details if you are interested in custom fitting. 10232100 Arizona Custom Grips About Magna-Tusk™ Ivory and Stag Grips: Magna-Tusk™ Ivory and Stag grips, a product of Arizona Custom Grips, are manufactured out of our high-grade, high density ivory material designed from the beginning as a premium, high-strength grip material. Vastly superior to standard bonded ivory or stag found on most factory and other aftermarket grips, Magna-Tusk™ is capable of withstanding the heaviest recoil and impact, and is the toughest alternative grip material available today, while still retaining the pristine look of real ivory or stag. It is rock-solid, stable, and water, chemical, and oil resistant. It is flame and heat resistant, and is entirely void-free, with over 10x the strength, durability, and impact resistance of alternative materials. Unlike with real ivory or stag, there is no routine care and maintenance involved, with no danger of it drying out and cracking if not maintained properly or if left in the heat. It is filled with premium natural compounds to produce outstanding aesthetic properties and mechanical performance. When aged with our natural aging process, it takes on the equivalent of a 100-year-old patina, with subtle grain details which many experts cannot tell apart from the real thing. In addition, the material has a fine grain structure, which holds intricate detail for carvings, artistic relief work, etc., found on many historic grips. 082920 About Our Aging Process: We go to great efforts to ensure that our Aged Ivory or Stag not only looks similar to, but in fact looks identical to the real thing. Our Magna-Tusk blanks will produce an aged Ivory grip unlike any other material made today. Our aged grips feature an authentic aged patina, just like the originals, with a process incorporating concentrated U.V. light (the essential aging property in natural sunlight), along with a developer/control agent that is put on the grips to carefully control U.V. absorption, in a sealed, high-oxygen environment to accelerate the natural aging process. Through this aging process, these grips become beautifully mottled, variegated, and weathered just like old, antique Ivory, and incorporate other authentic details found on original old Ivory as seen on many of the revolvers which belonged to gunfighters and lawmen of the Old West. As with real aged Ivory, Magna-Tusk develops a variegated patina due to its authentic grain structure, and natural aging produces an authentic appearance and genuine patina which extends into and below the surface. Not only does this give it the appearance of authenticity and depth, but this surface will not chip, crack, or peel like a superficially applied coating. With Magna-Tusk aged grips, most experts cannot tell them apart from a decades-old or even a centuries-old original. While the quality difference is somewhat noticeable in the photos, the difference is even more apparent when seen and handled in person. Many of our repeat sales are made by the very customers we sell to, who take their grips to the range, where our grips are immediately seen and noticed by others. If you are interested in ordering grips for a Brace of pistols, please order both sets together, and we will ensure a better matchup when selecting pairs. Dense, heavy, and solid, Magna-Tusk grips are in a class all their own. With our exclusive aging process, these grips are outstanding right out of the box, and will continue to improve over time. The more these grips are handled and used, the better they look! 082920 The photo used is a stock photo (a sample pair). Yours will appear similar to these. Customer satisfaction is important to us – we guarantee your complete satisfaction with every purchase!!

Price: 94.95 USD

Location: Mesa, Arizona

End Time: 2024-03-12T23:58:48.000Z

Shipping Cost: 5.99 USD