TECH LIGHTING KABLE LITE SYSTEM • 6 LIGHTS; 2 SURFACE MOUNT TRANSFORMERS • CABLE

Description: Tech Lighting Set of Modern Kable Ceiling Lighting System Six Lights on two strings Color: matte black • includes bulbs, transformers, turnbuckles, extra cable Complete Kable Lighting System • Six lights on two strings each of which is approximately nine feet long; comes with four turnbuckles; two surface-mount 150 W transformers, and extra cable and bulbs. Product Description: Cable LightingCable lighting systems have emerged as a contemporary design favorite due to their sleek, unobtrusive styling as well their extraordinary ability to be installed in even the most challenging of spaces. Although often lumped into the same category, cable lighting systems should not be confused with traditional track lighting or monorail lighting systems. - TIP: Easily make a complete cable lighting kit from any cable lighting compatible fixture by clicking the 'Make it a Kit' button on the fixture detail page. Cable Lighting Basics When should I use cable lighting? Cable lighting systems are most commonly used in spaces with challenging mounting surfaces. Consider them in rooms with very high ceilings, cathedral or vaulted ceilings and ceilings interrupted by soffits, beams or exposed ductwork. In these situations, short runs (under twenty feet) may typically be installed from wall to wall without any vertical support at all. In situations requiring cable runs longer than twenty feet, additional vertical support is recommended to prevent excessive tension from stressing the mounting points on the wall. In spaces with standard, flat ceilings, the use of cable lighting is largely a matter of design preference over other linear lighting systems such as monorail or traditional track lighting. Configuration Although cable lighting systems are relatively simple in theory, each manufacturer has a proprietary configuration process for their components. Brilliant Lighting offers a unique, manufacturer-neutral build your own cable lighting system wizard which allows customized cable lighting systems to be easily configured in just a few minutes. If you would prefer to assemble a system manually you should read the brief overview below which discusses common cable lighting components: Cable The primary support and conductive wire used in cable lighting systems is Kevlar-reinforced, tin-plated 10 gauge cable. Note that some support components for cable systems use thinner aircraft cable. Aircraft cable should never be used in place of standard cable lighting system cable. Although lighting system cable is usually bare, insulated cable is available as well for applications where the cable will pass through a wall and may contact something it shouldn’t. Turnbuckles Turnbuckles serve several purposes. Specifically, they: attach the cable to a wall or ceiling mount point expand and contract via a screw motion to apply and release tension on the cable run. may also serve as a powerfeed for the system by carrying power through the mounting wall to the system itself Anchors Anchors are similar to turnbuckles in that they attach the cable to a wall mount point. Anchors do not allow additional tension to be applied to a system. Surface Mount Transformers Transformers which are housed in finished enclosures designed to be attached over a power junction box in the wall or ceiling are referred to as surface mount transformers. These transformers are more common than remote transformers due to their ease of installation when remodeling. Remote Mount Transformers Remote mount transformers are enclosed in crude fire-code housings which are designed to be mounted in remote locations away from the cable lighting system (typically a nearby closet or within the wall itself.) Remote mount transformers offer a very clean look but are typically practical only in new construction projects where access to the area behind walls is available. When installing cable systems under irregular ceilings with exposed beams, it may be acceptable to tuck a remote mount transformer behind a beam rather than within the wall itself. Isolating Connectors Isolating connectors physically connect two lengths of cable while interrupting the flow of current between them. Since cable lighting systems may only carry 300 watts of power along any part of a run, isolating connectors allow continuous long cable runs with multiple, independently-powered segments. Vertical Supports Vertical supports should be used on cable runs over 20 feet or whenever a cable system will be used to support heavy pendant fixtures. Vertical stem supports are rigid pieces of metal (from 2” to 24” long) that mount directly to flat ceilings. More challenging installations will likely require flexible cable supports which may be any length and are easily installed on practically any irregularly shaped ceiling surface. Turn Kits Turn kits are used to change the direction of a cable lighting run. Turn kits are comprised of a pair of rigid stem supports attached to a cantilevered horizontal support cable. These kits only work for systems suspended two feet or less below a ceiling. Systems suspended further than this from the ceiling may be turned using a floating re-router…please call for details. This set includes six lights with MR-16 bulbs; two surface mount 150 W transformers; two approximately nine-foot cable runs that can be cut shorter. Extra cable if you want a longer run and six bulbs already installed plus two extra bulbs. Used but in like-new condition -------------------- See my other auctions, Click here. I'm a VERIFIED user of Paypal. This means that your Paypal-purchase from me is GUARANTEED! Through Paypal. Your item will ship out the next business day with this free payment service. Click on the link below. (It will help to join before the auction ends.) Use the link below to join: Pay me securely with PayPal!

Price: 499.99 USD

Location: San Francisco, California

End Time: 2024-12-17T03:00:00.000Z

Shipping Cost: N/A USD