JeffTron AEP MOSFET

Description: JeffTron AEP MOSFET Professionally made MOSFET designed for Airsoft Electric Pistols (AEP).This device increases rate of fire and the wiring is far improved over basic wiring.Can be installed without modifications into these AEP's:Cyma CM.030 Glock 18CCyma CM.121 Desert EagleCyma CM.122 SIG P226Cyma CM.123 Colt M1911Cyma CM.125 H&K USPCyma CM.126 Beretta M92FCyma CM.127 PhantomCyma CM.128 HI-CAPA 5.1Tokyo Marui Glock 18C AEPTokyo Marui Beretta M93R AEPTokyo Marui Beretta M9A1 AEPTokyo Marui HK USP AEPUmarex HK USP AEPDouble Eagle M81 USPRECOMMENDED BATTERY:1. Lipol 7.4v (2S) Turnigy Nano-Tech Plus 300mAh 70C~140C2. Lipol 7.4v (2S) Turnigy nano-tech 300mah 45~90C3. Lipol 7.4v (2S) Turnigy nano-tech 300mAh 35~70CSPECIFICATIONS:- Very small device dimension - used Micro mosfet III- Prepared wiring allows fast and easy installation into the pistol. Simply solder wires to the motor and trigger contacts- On the devices are pre-soldered high quality power wires 0,5 qmm (AWG20) with silicone insulation (length 210mm from mosfet) and blue wires 0.25 qmm (AWG24) with PVC insulation (length 110mm from mosfet)- Connector for battery is used JST-SYR 2 pin- Board covered by conformal coating, it protect device against water- If you want to use your own wires or connector, choose Micro mosfet III without wiring- Can be used with any AEP upgrade, because it was designed for spring up to M170 (equivalent for current 90A single shot fire or 35A burst fire for max. 30s)- Recomended to use 7,4V lipol battery, but device is specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)- 6 wires connection- Device size 16x6,4x3,5mm- No current consumption in the idle mode- No sparking on switch contacts- In auto fire mode piston stops in random position due the mechabox design- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearboxDEVICE INSTRUCTIONS: you can download installation manual in English herePACKING:- Device with wiring and JST-SYR connector- Installation manual in EnglishWARNING: Installation of this device leaves to expert, who could solder and disassemble airsoft pistol. Never user soldering gun!WIRING CONNECTION INTO THE GUN: see product images. JeffTron AEP MOSFET Professionally made MOSFET designed for Airsoft Electric Pistols (AEP). This device increases rate of fire and the wiring is far improved over basic wiring. Can be installed without modifications into these AEP's: Cyma CM.030 Glock 18CCyma CM.121 Desert EagleCyma CM.122 SIG P226Cyma CM.123 Colt M1911Cyma CM.125 H&K USPCyma CM.126 Beretta M92FCyma CM.127 PhantomCyma CM.128 HI-CAPA 5.1Tokyo Marui Glock 18C AEPTokyo Marui Beretta M93R AEPTokyo Marui Beretta M9A1 AEPTokyo Marui HK USP AEPUmarex HK USP AEPDouble Eagle M81 USPRECOMMENDED BATTERY:1. Lipol 7.4v (2S) Turnigy Nano-Tech Plus 300mAh 70C~140C2. Lipol 7.4v (2S) Turnigy nano-tech 300mah 45~90C3. Lipol 7.4v (2S) Turnigy nano-tech 300mAh 35~70CSPECIFICATIONS: - Very small device dimension - uséd Micro mosfet III- Prepared wiring allows fast and easy installation into the pistol. Simply solder wires to the motor and trigger contacts- On the devices are pre-soldered high quality power wires 0,5 qmm (AWG20) with silicone insulation (length 210mm from mosfet) and blue wires 0.25 qmm (AWG24) with PVC insulation (length 110mm from mosfet)- Connector for battery is uséd JST-SYR 2 pin- Board covered by conformal coating, it protect device against water- If you want to use your own wires or connector, choose Micro mosfet III without wiring- Can be uséd with any AEP upgrade, because it was designed for spring up to M170 (equivalent for current 90A single shot fire or 35A burst fire for max. 30s)- Recomended to use 7,4V lipol battery, but device is specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)- 6 wires connection- Device size 16x6,4x3,5mm- No current consumption in the idle mode- No sparking on switch contacts- In auto fire mode piston stops in random position due the mechabox design- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearboxDEVICE INSTRUCTIONS: you can download installation manual in English here PACKING: - Device with wiring and JST-SYR connector- Installation manual in EnglishWARNING: Installation of this device leaves to expert, who could solder and disassemble airsoft pistol. Never user soldering gun! WIRING CONNECTION INTO THE GUN: see product images. × × × × × × Buy now and save! Shipping info Click the Shipping & Payments tab above the listing description for more info Click the Shipping & Payments tab above the listing description for more info! Additional delivery notes PICK UP OPTION Sorry, our items are NOT available for pick-up. PAYMENT Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay. We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus). The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws. Thank you for shopping with us on eBay! Additional Information No additional information at this time Ask seller a question You might also like 1/32" Airsoft 70D Die Cut Neoprene Buffer ASG Airsoft Ultimate 28TPA CNC Long Motor ASG Airsoft Ultimate 16TPA CNC Short Motor ASG Airsoft Infinity Boost 40K RPM 14TPA Short Motor Contact To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist. Ask seller a question © BRILL ARMORY Shipping & Payments Click the Shipping & Payments tab above the listing description for more info Payment Accepted Payment Methods Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay. We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus). The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws. Thank you for shopping with us on eBay! Returns Returns are accepted Items must be returned within 30 days of the auction ending Buyer will pay for return shipping. eBay integration by

Price: 27 USD

Location: Los Angeles, California

End Time: 2024-09-16T02:29:03.000Z

Shipping Cost: 5 USD