Foxwell NT630 Plus OBD2 Scanner ABS Bleeding SRS SAS Code Reader Diagnostic Tool

Description: Foxwell NT630 Plus OBD2 Scanner ABS Bleeding SRS SAS Code Reader Diagnostic ToolABS SRS Reset ScannerFoxwell NT630 Plus ABS & SRS Reset SAS Calibration Diagnostic Tool :[Foxwell NT630 Plus ABS & SRS Reset Tool Features]ABS Auto Bleed: The air will get inside when the brake system opened to replace components such as calipers, wheel cylinders, the master cylinder, or brake lines or hoses. To get a firm brake pedal, the air has to be removed by bleeding the brakes. This abs auto bleed scan tool will help bleed the brake, cycling the pump and valves during the bleeding process.Bidirectional Control/ Active Test: Do the active test on the ABS/Airbag system and components, including Auto Bleed Test/ Setup SDM Serial Number/ ABS Manual Control Tests/ ABS Motor Test/ ABS Version Test/ Actuator Tests, etc.4 Modules Diagnosis:Scan ABS/SRS/Airbag/ OBD2 modules error faults to check the issues that caused the warning light on and turn off the MIL after maintenance.ABS/ Airbag/ SRS Sensor Reset & Calibrate: Reading ABS and SRS/ Airbag error codes, point out the car issues and guide you to repair them. Besides the normal diagnostic functions that others can do, it will reset the ABS & SRS system after maintenance to let the ECU identify the new components to make it work normally.SAS(Steering Wheel Angle Sensor) Calibration: calibrates of the steering angle sensor and stores the current steering wheel position as straight-ahead in the sensor EEPROM. On successful calibration of the sensor, its fault memory is automatically cleared.Self-Check E-mission Condition: Scan all OBD2 modules, show the I/M readiness status and check if the vehicle is ready for the annual inspection of S-M-O-G test.[Foxwell NT630 Plus ABS & SRS Reset Tool Support Functions] --- ABS/SRS/ Airbag Bidirectional Control/ Active Test --- The abs scan tool code reader temporarily allows you to do bi-directional diagnostic tests on the system and components of anti-lock brake systems and air bags, sends commands to the integrity of abs srs systems or vehicle’s modules to test the working status without using the vehicle controls and and when you exit the test, the system/component returns to normal operation. (Note: All the functions mentioned are up to your vehicle condition, please confirm the compatibility before purchase!) Attention Please: 1. Before bleeding the brake system, make sure no diagnostic codes are presen. 2. Do not let the master cylinder run dry during the brake bleeding procedure. 3. After bleeding the brake system, check the brake pedal for excessive travel or a “spongy” feel. Bleed again if either condition is present.Auto Bleed Test, Automated Bleed, or Service Bleed – removes air from the internal brake fluid chambers after servicing the brakes.ABS Manual Control Tests – allows to manually control the actuators in order to test ABS motors, solenoids, solenoid enable relays, EMBs, and more.ABS Motor Test – allows to manually control the ABS pump motor.ABS Version Test – displays the name of the brake system and the ABS controller version number, software ID, and sequence value.Actuator Tests – allows to manually control the actuators in order to test AYC valves, inlet valves, outlet valves, pump motors, and TRACS valves.Automated Test - automatically commands each solenoid valve and the pump motor on and off to test for proper operation.Brake Bleed Preparation Test - prepares the brake lines for bleeding by clearing air from the modulator. The test rehomes all the ABS and TCS motors, cycles the TCS motors, and then returns all motors to the “home” position at the bottom of the bore.Setup SDM Serial Number (Air Bag Sensing and Diagnostic Module) - allows to program a new air bag serial number into the dash integration module (DIM). You use this test after installing a new air bag; otherwise a diagnostic trouble code will be set when you turn on the ignition.Function Test - automatically commands the ABS relay, valve solenoids, and pump motor on and off to test for proper operation. Gear Tension Relief Test - relieves tension from the ABS motor gears so you can separate the ABS motor pack from the ABS hydraulic modulator. Hydraulic Control Tests - allows to manually engage and disengage the ABS solenoids for troubleshooting the hydraulic functions. Idle Up Manual Control Test - allows to manually control the idle up actuators. Lamp Tests - allows to manually control the ABS or TCS warning or indicator lamps. Motor Rehome Test - prepares the brake lines for bleeding by clearing air from the modulator. The test returns all ABS motors to their “home” positions. Pump Motor Tests - allows to manually control the pump motor. Relay Test - allows to manually engage and disengage either the ABS or TCS relays in order to test relay operation. Requested Torque Test - allows to manually control the engine torque to test for proper operation of the traction control system (TCS). Solenoid Tests - allows to manually control the inlet and output valve solenoids. System Identification - displays information about the brake system, the vehicle, and the ABS controller. TCS Test - allows to control the pump motor in order to apply fluid pressure to the front wheel circuits. Traction Control System (TCS) Manual Control Tests - allows to perform motor tests and an adjuster assembly control test. Voltage Load Test - “loads” the ABS battery supply circuit to test for adequate battery capacity.[Foxwell NT630 Plus Support Language]The device only can install 2 languages , one is English , the other one you can choose from the following : English, Korea, Spanish, Portuguese, French, Thai, Hungarian, Swedish, Dutch, Japanese, Italian, Russian,German Full OBDII Engine Check Code Reader obd2 diagnostic code reader provides comprehensive OBDII diagnostics for global OBDII/EOBD vehicles, reads and clear codes, turns off MILs, requests and records live sensor data,ect.except live data reading. In addition, it supports all 10 OBDII test modes, includs the mode 6 test. Powerful graphing capability gives you the "real picture" of what's going on in the vehicle, which allows you focus on any suspicious or symptom-specific data parameters. $01 - Request Current Powertrain Diagnostic Data$02 - Request Powertrain Freeze Frame Data$03 - Request Emission-Related Diagnostic Trouble Codes$04 - Clear/Reset Emission-Related Diagnostic Information$05 - Request Oxygen Sensor Monitoring Test Results$06 - Request On-Board Monitoring Test Results for Specific Monitored Systems$07 - Request Emission-Related Diagnostic Trouble Codes Detected During Current or Last Completed Driving Cycle$08 - Request Control of On-Board System Test or Component$09 - Request Vehicle Information$0A - Request Emission-Related Diagnostic Trouble Codes with Permanent Status [Foxwell NT630 Plus OBD2 Engine Support Car List]Asian Car (2013-2019 model) for AU Ford ( For Australian Market Only ), for Acura, for Daewoo, for Honda, for Holden, for Hyundai, for Isuzu, for Infiniti, for Kia, for Lexus, for Mazda, for Mitsubishi, for Nissan, for Perodua, for Proton, for Scion, for Subaru, for Suzuki, for Toyota. European Car (2001-2019 model) For Audi, for Abarth, for Alfa-Romeo, for Aston Martin, for BMW, for Bugatti, for Bentley, for Citroen, for Dacia, for EU Ford, for Ferrari, for Fiat, for Jaguar, for Lamborghini, for Lancia, for Land Rover, for Maserati, for Mini, for Maybach, for Mercedes Benz, for Opel, for Peugeot, for Porsche, for Renault, for Rolls, for Saab, for Seat, for Skoda, for Smart, for Sprinter, for Vauxhall, for Volvo, for VW, for VWCV. American (USA) Car (1996-2019model) : for Chrysler, for Ford, for GM ( including brazilian car maker ) Doesn't Support UAZ,LADA,VAZ [Foxwell NT630 Plus Free Upgrade Forever !!!]NOTE: NT630 plus use new program to update. not foxscanner, please go to new website (check back of scanner) download FoxAssist. or you can contact me directly. 1. Go to the Foxwell official website :Choose your product ,Under the page,click the Download,then download FoxAssist Installer.zip update clients software. 2. Register foxwell account and complete the related information at FoxAssist client software . 3. Connect NT630 Plus with computer by USB, click "Activation" menu. 4. It can indentifies your sn number automatic, choose your sn number and click Activation 5. Go to "Download" page, choose all software, and then click "upgrade" 6. Wait several minutes, update will be done, enjoy new software [Package List]1 pc x Foxwell NT630 Plus1 pc x User's Guide1 pc x Memory Card1 pc x USB Cable1 pc x Diagnostic Cable1 pc x plastic case or carton box PaymentDelivery detailsTerms of salesAbout usContact usPayment We accept all common forms of payment such as Credit cards、Debit card、Google Pay ect. Please contact us if you need to use another method to pay. Payment should be made within 4 days after bidding ends. Otherwise a Unpaid Item case will be opened to you. We are not responsible for buyers’ local taxes. Please include your special requests in eBay note if there is any.Delivery detailsShipping methods: USPS First Class Mail Service /USPS Priority Mail Service/UPS Surepost SERVICE/ UPS GROUND SERVICE I will process your order within one business day (excluding holiday and weekend)If you have any problems, you can contact me first or local USPS, UPSTerms of salesPlease do not hesitate to leave us your PositiveFeedbackandgood review If you are satisfied with our productsIf youare unsatisfiedwith your purchase,please email us first to get a better solution before you leaveaneutralornegative feedback, we work hard to make sure every customer 100% satisfied and resolve any problem for you. Thank you for your kindness. About usWe are a professional Authorized dealers of AUTEL, LAUNCH,ANCEL,FOXWELL, OBDSTAR， AUTOPHIX, KZYEE, NEXAS,Autek ，WOYO，etc. We support remote assistance by TeamViewer if you have any difficulty in software installation. Contact usAny questions, you can feel free to contact me by ebay message or whatsapp.Due to time difference, I may not be able to reply immediately, but I will reply within 24 hoursPlease contact me first before giving negative feedback or opening case. Wish we can solve the problem peacefully. Working hours:0:00 am - 3:00 am Pacific Time， 6:00-9:00 pm Pacific Time, 11:00 pm - 12:00 pm Pacific Time. On Oct 15, 2024 at 04:20:10 PDT, seller added the following information:

Price: 149.98 USD

Location: Monroe Township, New Jersey

End Time: 2025-01-10T01:41:07.000Z

Shipping Cost: 0 USD