Fluke ESA615 230V ac Electrical Safety Analyzer Medical Equipment Tester ESA-615

Description: The Following Items Are Included: Fluke ESA615 230 V ac Electrical Safety Analyzer (BC# -L/T*) (2) 1000V Hard Point Test Leads Power Cord USB PC Interface Cable User Manual On CD-ROM Carrying Case (G) BE SURE TO CHECK OUR EBAY STORE FOR OTHER ITEMS! This Item Has A Current Calibration! Fluke ESA615 230 V AC Electrical Safety AnalyzerThe ESA615 Electrical Safety Analyzer brings fast and simple automated testing to a portable analyzer for healthcare technology management professionals that perform electrical safety testing on medical equipment both in the field and in facilitiesThe ESA615 is an all-in-one solution with a multimeter, safety analyzer and ECG simulator in a single test instrumentIncludes Carrying Case & Accessories As Listed Above! Working Condition: ExcellentCondition: RefurbishedWarranty: 1 YEAR WARRANTY Fluke ESA615 Electrical Safety AnalyzerThe ESA615 Electrical Safety Analyzer brings fast and simple automated testing to a portable analyzer for healthcare technology management professionals that perform electrical safety testing on medical equipment both in the field and in facilities. Whether it is simple testing or comprehensive analysis, the ESA615 can do it all. This multifaceted device performs all primary electrical safety tests, including line (mains) voltage, ground wire (protective earth) resistance, insulation resistance, device current, and lead (patient) leakage tests. It also offers ECG simulation and point–to-point voltage, leakage, and resistance tests. Versatile to global electrical safety standards of choice, ESA615 tests to ANSI/AAMI ES1, NFPA- 99, IEC62353 (VDE751) IEC60601-1 (2nd and 3rd editions) and AS/NZS 3551. The ESA615 is an all-in-one solution with a multimeter, safety analyzer and ECG simulator in a single test instrument.Automated: Pre-set templates allow you to test to the global standard of your choices at the push of a button. Let the unit guide you through the test steps quickly and accurately in three simple steps: Select the test sequence corresponding to your standard of choice Initiate the automated test sequence. Store the results on-board or wirelessly export to your PC in seconds. It is that easy. The automated test sequences are easily customized to suit individual testing requirements.Portable: The ESA615 is a small, lightweight analyzer with an integrated handle to carry from place to place for on-the-go field service. It is designed for operation in tight spaces, and is easy to fit on any cart. A light, protective carrying case makes it easy to store and transport.Simple: A push-button interface allows quick access to highly-comprehensive functions and features, and an intuitive interface guides the user through tests. The ESA615 features a large display for clear indication of available functions, set-up criteria, device under test receptacle conditions, and test results. Data can be entered quickly with a plug–and-play keyboard, barcode scanner and/ or on-board data entry interface. Data archival is fast and simple with wireless communication or through a removable memory card with capacity for thousands of test results.Features: On-board automation with automated test sequences for rapid testing and easy compliance to key global electrical safety standards (ANSI/AAMI ES1 (NFPA-99), IEC62353 (VDE751), IEC60601-1 2nd and 3rd editions, and AS/NZS 3551) Portable, ergonomic design with an integrated handle and tilt stand Human-factors-designed user interface for streamlined testing ECG waveform tests and dual-lead measurements combine the functionality of a simulator, multimeter and safety analyzer in a single test tool 20 A at 120 V current capability Five applied parts jacks and easy ECG snap connection; optional expander box for up to 12-lead ECG testing Easy data entry through barcode scanner, external keyboard or on-board keypad Wireless communication plus removable memory card for fast and convenient data storage and exchange Replaceable mains fuses keep your unit in the field and out of the repair shop Custom language selections include English, French, German, Spanish, Italian and Portuguese Large, easy-to-read display with adjustable contrast Rigorously tested for rugged field applications, with CE and CSA in addition to Fluke quality—ruggedness for long-term reliability Specifications: Voltage Range (mains voltage) 90 V ac rms to 132 V ac rms Range (accessible voltage) 0 V ac rms to 300 V ac rms Accuracy ± (2 % of reading + 0.2 V) Voltage tests Mains and point to point Earth resistance Modes Two-Wire Test current/Ranges/Accuracy > 200 mA ac / 0 Ω to 2 Ω / ± (2 % of reading + 0.015 Ω) Resistance tests Earth resistance and point to point Equipment current Mode AC rms Range/Accuracy 0 A to 20 A ± (5 % of reading + (2 counts or 0.2 A, whichever is greater)) Duty cycle 15 A to 20 A, 5 min. on/5 min. off 10 A to 15 A, 7 min. on/3 min. off 0 A to 10 A continuous Leakage current Modes( Modes are available in all leakage tests with the exception of MAP leakages that are available only in true-rms) AC + DC (True rms)AC onlyDC only Patient load selection (input impedance) AAMI ES1-1993IEC 60601: Crest factor ≤ 3 Ranges 0 µA to 199.9 μA200 µA to 1999 μA2 mA to 10 mA Frequency response/accuracy DC to 1 kHz / ± (1 % of reading + (1 μA or 1 LSB, whichever is greater))1 kHz to 100 kHz / ± (2 % of reading + (1 μA or 1 LSB, whichever is greater)) 1 kHz to 5 kHz (current > 1.6 mA) / ± (4 % of reading + (1 µA or 1 LSD, whichever is greater))100 kHz to 1 MHz / ± (5 % of reading + (1 μA or 1 LSB, whichever is greater)) Accuracy for Isolation, MAP, Direct AP, Alternative AP, and Alternative Equipment leakage tests all ranges are: At 120 V ac + (2.5 µA or 1 LSD, whichever is greater) For Alternative equipment, Alternative AP, and Direct AP leakage tests, the leakage values are compensated for nominal mains as per 62353. Therefore, the accuracy specified for other leakages is not applicable. Leakage tests Ground wire (earth) Chassis (enclosure) Lead to ground (patient) Lead to lead (patient auxiliary) Lead isolation (mains on applied part) Direct equipment Direct applied part Alternative equipment Alternative applied part Point to point Mains on applied part test voltage 100 % ± 7 % of Mains for AAMI, current limited to 1 mA ± 25 % per AAMI 100 % ± 7 % of Mains for IEC 62353 current limited to 3.5 mA ± 25 % per IEC 62353 100 % ± 7 % of Mains for IEC 60601-1 current limited to 7.5 mA ± 25 % per IEC 60601-1 Differential leakage Ranges 75 µ A to 199 µA 200 µA to 1999 µA 2 mA to 20 mA Accuracy ± (10 % of reading + (2 counts or 20 µA, whichever is greater)) Insulation resistance Ranges/Accuracy 0.5 MΩ to 20 MΩ / ± (2 % of reading + 0.2 MΩ)20 MΩ to 100 MΩ / ± (7.5 % of reading + 0.2 MΩ) Source test voltage 500 V dc or 250 V dc(+ 20 %, -0 %) 2.0 ± 0.25 mA short-circuit current Insulation resistance tests Mains-PE, AP-PE, Mains-PE, Mains-NE (non-earthed accessible conductive part) and AP-NE (non-earthed accessible conductive part) ECG performance waveforms Accuracy ± 2 %± 5 % for amplitude of 2 Hz Square wave only, fixed @ 1 mV Lead II configuration Waveforms Rates: ECG complex: 30 BPM, 60 BPM, 120 BPM, 180 BPM, and 240 BPMVentricular fibrillation:Square wave (50 % duty cycle): 0.125 Hz and 2 HzSine wave: 10 Hz, 40 Hz, 50 Hz, 60 Hz, and 100 HzTriangle wave: 2 HzPulse (63 ms pulse width): 30 BPM and 60 BPM Test standards Available selections ANSI/AAMI ES-1, IEC62353, IEC60601-1, and AS/NZS 3551 Built-in test sequences IEC60601-1 3rd Edition Patient Monitor, Defibrillator, Infusion Pump, Ultrasound Device, Generic Device and System IEC62353 Patient Monitor, Defibrillator, Infusion Pump, Ultrasound Device and Generic Device NFPA-99 (Hospital) Patient Monitor, Defibrillator, Infusion Pump, Ultrasound Device and Generic Device ANSI/AAMI ES1 Patient Monitor, Defibrillator, Infusion Pump, Ultrasound Device and Generic Device Communications USB device upstream port Mini-B connector for control by a computer USB host controller port Type A, 5 V output, 0.5 A max load. Connector for keyboard and barcode reader Wireless IEEE 802.15.4 for control by a computer Modes of operation Manual and remote Power ratings Mains voltage outlet 120 V ac 230 V ac Mains voltage inlet power range 90 V ac rms to 132 V ac rms 180 V ac rms to 264 V ac rms Maximum current 20 A 16 A Hz 47 to 63 Hz 47 to 63 Hz Environmental Operating temperature 10 ºC to 40 ºC (50 ºF to 104 ºF) Storage temperature -20 ºC to 60 ºC (-4 ºF to 140 ºF) Operating humidity 10 % to 90 % non-condensing Altitude 120 V ac mains supply voltage up to 5000 meters 230 V ac mains supply voltage up to 2000 meters For full Fluke ESA615 product specifications, please click here: Fluke ESA615 Please check our Huge Inventory with savings of up to 80% off of retail on Cat5/5e/6 LAN Cable Certifiers and Fiber Optic OTDR's, Fusion Splicers, CATV Meters, Fiber Optic Kits, Sources, Meters, Tools, Network Analyzers and much more. Here is a Link to our Ebay Test Equipment Store. All of our Test Equipment is backed with a Full Warranty and unbeatable customer support & service. Please don't hesitate to contact us for a Quote on Something you don't see in our inventory, sometimes we have items that may have not been listed or processed yet. Test Equipment Store Offers a wide range of Refurbished Telecom/ Datacom Tools and Test Measurement Equipment. Which includes Fiber Optic Test and Splicing tools, Fusion Splicers, OTDRs, Copper and Fiber Cable Certifiers, CATV Test Equipment, Cable and Antenna Analyzers, Network Analyzers and much more! We carry a large inventory of quality refurbished and used test equipment from all the major manufacturers. If you are looking for multiple quantities or if we don't have a listing for a particular item that you are looking for. Please contact us as it may be fresh inventory waiting to be listed or we'll be glad to find it for you at the best price possible and put up an eBay listing for you! We Ship World Wide! We will attempt to ship your item(s) within 24 hours after payment has been received. To get a real-time shipping quote to your destination, enter your country and zip / postal code information into the shipping calculator and click "Get Rate".Many countries impose their own customs, duties, tariffs, taxes, etc. on items being shipped from a foreign country. We do not cover those cost's and we recommend that you contact your countries customs agency for that information.We Offer Multiple Quantity Price & Shipping Discounts, Email Us If You Are Interested In Larger Quantities. We accept credit card payment transactions via the online checkout system! The checkout process is designed so that it communicates with the merchant to confirm that payment has been made and cleared. Other methods of payment are outlined through the online checkout process. Winning bidders must contact us within 3 days after auction close if special payment arrangements are needed. Your payment is expected within 5 days after the auction close. Unpaid auctions will be forfeited after 5 days of the auction close and the Item(s) will be relisted for sale. Items will be shipped within 24 hours (1 Business Day) upon receipt of payment from the winning bidder. (Certain orders may take longer for processing due to comprehensive final service inspections) A Shipment Tracking number(s) will be provided to inform Buyers of their expected ETA (Estimated Time of Arrival). Tracking number(s) will be provided the same day as order shipment. Thank you ALL MAJOR CREDIT CARDS & PayPal ACCEPTED Sell Smarter with Kyozou.Inventory and Ecommerce Management

Price: 4889 USD

Location: Southgate, Michigan

End Time: 2024-09-14T17:32:09.000Z

Shipping Cost: N/A USD