Description: Click Window To Watch Video Demonstration STEP 5. APPLICATION DEMONSTRATIONS Condition the ambient temperature to 75°F for best results. Ensure that the work area is dust free and well ventilated. MAX CLR-HP A/B is self-levelling and will continue to flow until it polymerization converts it to a solid phase. It can be applied by using a bristle or high-density foam brush/roller or poured into place. MAX CLR-HP A/B is self levelling, ensure the surface is level and secure any leaks by using tape to create a temporary patch and prevent leakage. ROTO-COATING OF MAX CLR-HP A/B ON WOOD TURNED BOWLClick Window To Watch Video Demonstration Commercial Restaurant Table Top Click Window To Watch Video Demonstration HOW TO APPLY EPOXY RESIN ON TABLE TOPS The video will open in a new window Multiple Pour Or Layering For Thick Coat Application Click Window To Watch Video Demonstration EPOXY THICK COATING APPLICATION MULTIPLE POURINGThe video will open in a new window AIR BUBBLE REMOVAL TECHNIQUE Click Window To Watch Video Demonstration HOW TO REMOVE AIR BUBBLES FROM AN APPLIED EPOXY COATING, ALSO HELPS WITH LEVELING AND FLOW - YouTube Video will open in a new window STEP 6. CURING To achieve the best cure results, the ambient condition should be between 75°F to 85°F and the relative humidity is below 80%. The colder the temperature the longer takes to fully cure. Use an infrared lamp to warm the ambient temperature. Infrared lamps also work well for warming large work areas. Post Curing at 150°F for 2 hours will accelerate full curing. Rinse the surface with warm water and mild detergent before use. CUTTING AND POLISHING Allow to fully cure for 48 hours before polishing or machining. MAX CLR-HP A/B can be cut, ground or CNC or lathe machined to shape. Polishing improves scratch resistance. The transparency is also restored after machining by wet sanding and then polish with abrasive free wax or polish. Click On The Picture To View Test Video. The Video Will Open In A New Window MAX CLR CUT AND POLISHED Video will open in a new window POLISHINGClick On The Picture To View Test Video. The Video Will Open In A New Window HOW TO POLISH EPOXY COATED TABLE TOP COATINGS TO GLASS-LIKE FINISH - YouTube Video will open in a new window DEGLOSSING Once the MAX CLR-HP A/B fully cures, deglossing the surface to create a satin finish can be easily done using an abrasive pad. In this demonstration, a SCOTCHBRITE pad was used to de-gloss the surface. Note the dramatic decrease in gloss after a light polishing with the abrasive pad. Very-fine sandpaper (wet-sanding) also works well. PHYSICAL AND MECHANICAL PROPERTIES Viscosity Density Form and Color 800 – 1,200 cPS @ 25°C Mixed 1.10 g/cc Clear Transparent Liquid Mix Ratio 100 Parts to 50 Parts A By Weight or by Volume 2:1 (Part A to Part B) Working Time 45 Minutes @25°C (77°F 100-gram mass) Peak Exotherm 70°C (158°F, 100-gram mass) Handle Time Full Cure Time 5.5 Hours 36 Hours minimum @ 25°C (75°F) Hardness 72± 5 Shore Tee-Peel Strength 5.7 Lbs per inch Width Tensile Shear Strength 1,300 psi @ 25°C (77°F) 800 psi @ -80°C (-112°F) 550 psi @ 100°C (212°F) Elongation 9.0% @ 25°C (77°F) Compressive Strength 2,200 psi Heat Distortion Temp 80°C (176°F) HOT WATER IMMERSION TEST WOOD COATED MUGClick On The Picture To View Test Video. The Video Will Open In A New Window Video will open in a new window PHYSICAL PROPERTIES AND MECHANICAL PROPERTIES Density 1.10 G/CC Form and Color Clear Liquid Viscosity 2,800 – 3,200 cPs @ 25ºC Mixed Mix Ratio 50 Parts “B” to 100 Parts “A” By Weight Working Time 45 – 50 Minutes @ 25ºC (100 Gram Mass) Peak Exotherm 70ºC (100 Gram Mass) Thin Film Set Time (Dry to the Touch) 4 to 6 Hours Handle Time (Green Strength) 8 Hours Full Cure Time 5 to 7 days @ 25ºC Accelerated Cure Time 8 hours at 25ºC plus 1 hour at 100ºC Hardness 80 ± 5 Shore D@ 25ºC Tee-Peel Strength 5.7 Lbs. per inch Width @ 25ºC Tensile Shear Strength 8412 psi - 58 MPa @ 25ºC Tensile Modulus 348,000 psi - 2.4 GPa @ 25ºC Compressive Strength 8992 psi- 62 MPa @ 25ºC Compressive Modulus 203,053 - 1.4 GPa @ 25ºC Elongation 3.0% @ 25ºC Flexural Strength 12,100 psi - 84 MPa @ 25ºC Flexural Modulus 406,000 psi- GPa @ 25ºC Heat Deflection Temp. 90ºC CHEMICAL RESISTANCE PERFORMANCE FULL IMMERSION at 30°C MEASURED PERCENT CHANGE IN WEIGHT SPECIMEN CURE CYCLE 7 days @ 25ºC plus 1 hour at 100ºC -1 CUBIC INCH SPECIMEN SIZE REAGENT 3 days 28 days Deionized Water 0.09 .10 Sea Water 0.11 0.11 Methanol 7.93 -2.41 Ethanol 50% 1.98 2.18 Toluene 0.40 2.86 Xylene 0.04 0.05 Butyl Cellosolve 16.63 5.31 MEK Destroyed Destroyed 10% Lactic Acid 1.81 5.42 10% Acetic Acid 0.11 0.45 70% Sulfuric Acid 0.08 0.14 50% Sodium Hydroxide 0 0 10% Sodium Hypochlorite 0.51 1.36 IMPACT RESISTANCE OF MAX CLR-HP A/B IMPORTANT NOTICE The user should thoroughly test any proposed use of this product and independently conclude the satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval. The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use. There is no warranty of merchantability for fitness of use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.
Price: 37.84 USD
Location: Ontario, California
End Time: 2024-01-28T21:09:10.000Z
Shipping Cost: 0.72 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
TWO COMPONENT EPOXY SYSTEM: Crystal Clear & Color Stable
Country of Manufacture: United States
MPN: MAXCLRHP24OZ
Modified Item: No
California Prop 65 Warning: SARA TITLE III SEC. 304 EHS RQ (lbs) N/A SEC. 302 EHS TPQ (lbs) N/A SEC. 312 Hazard Category DELAYED HEALTH HAZARD SEC. 313 Hazard Category NONE CERCLA (40 CFR 302.4 HAZARDOUS SUBSTANCE & REPORTABLE QUANTITIES): This product does NOT contain any hazardous substances listed in 40 CFR 302.4. CALIFORNIA PROP. 65 Resins based on rosin-derived resins are NOT listed on California’s Prop. 65 toxic substance list. ODC STATUS/CLEAN AIR ACT/CLEAN WATER ACT: The components of this product are NOT found to contain any ozone depleting compounds or hazardous air pollutants. None of the chemicals in this product are listed as Hazardous Substances, Priority Pollutants or Toxic Pollutants under the CWA
Brand: MAX CLR-HP Resin system
Type: Epoxy Resin
Unit Type: fl oz
CASTING, COATING, IMPREGNATING: High-Performance Version Of MAX CLR Resin System
Model: MAX CLR HP A/B 24 OUNCE KIT
Country/Region of Manufacture: United States
Unit Quantity: 24
FOOD SAFE: For Coatings And Adhesive Applications
