Cardinal

Electric Water Pump - EWP115 (NYLON) Combo (12V) (Davies Craig) (Part #8930)

Description: Electric Water Pump - EWP115 (NYLON) Combo (12V) (Davies Craig) (Part #8930) The EWP®115 Nylon 12V is available for purchase in following options:Pump Only (Part #8125) Kit (Part #8025)Combo with Controller (Part #8930) *This ListingTake total control of your engine cooling with the Davies Craig EWP®115 Nylon Electric Water Pump and LCD EWP®/Fan Digital Controller. The Controller will also manage the operation of your Thermatic® Fan. The EWP®115 pump is suitable for small, medium, large, high-performance and 4WD vehicles. It improves engine cooling control and capacity whilst giving you more power and torque and improved fuel economy.Mechanical belt-driven water pumps run directly off the motor and sap engine power … the EWP®115 is hardwired into your electrical system, by-passing the engine and releasing up to an additional 10kw (13hp). Combined with the LCD EWP®/Fan Digital Controller, the pump continues to run after you’ve switched off, eliminating “heat soak” and extending engine life. Our EWP range are also extensively used in Intercooler Applications. COMBO CONTENTSPART DESCRPTIONUNITSEWP®115 - NYLON 12v Assembly1HOSE CLAMP4Wiring Harness - EWP & Fan controller1EWP/Fan Digital controller1Adapter - Nylon - In Line, 35mm (2 x 1/4" NPT)(*As of Sept 2021 the inline adapter changes to 38mm)11/4" NPT Nylon - Bung1U-Bracket - For #80021Mounting Plate - For #80021SCREW - SELF TAP 8X3/8 BZ1BLUE 6mm Ring Terminal - B2-61Sensor Thermal - coolant temp - ¼" NPT thread1 TECHNICAL SPECIFICATIONSEWP115 - ELECTRIC WATER PUMP LCD CONTROLLEROperating voltage3V DC to 15V DCVoltage range12V DC to 29V DCMaximum current10A @ 13VDisplay LCD size64.6mm (2.54”) x 55.6mm (2.19”)Flow rate (max)139 L/min (36.7 US gal/min) @ 13V DCMaximum current12AmpsOperating temp.-40° to 120°C (-40° to 248°F)Warning alarmHigh & low Temp., Above set temp., Sensor short circuit, Pump error, High & low voltage and Sensor open circuitPump designClockwise centrifugal with volute chamberTargeted (set) temperaturesSingular degrees from:40°C (104°F) to 110°C (230°F)Pump weight920 grams (2.3 lb)MemorySet & targeted temperaturePump materialNylon 66, 30% glass-filledFan cut-in temp.3°C (5.4°F) above the targeted (set) temperatureBurst pressure500 kPa (72.5 psi)Controller typePCB with micro-processorSealCeramic face sealSensor typeThermister in housingSelf PrimingNo, none of our pumps are self-primingFits hose sizes35mm to 51mm (1.38” to 2”)Overrun/ shutdown-10°C (14°F) below set/target temperature or 3 minutes Push-On fitting Size EWP Inlet & Outlet 38mmwith 3mm Sleeve (#8510) 44mmwith 6mm Sleeve (#8511) 51mm IndicatorsTemperature, power, EWP, test, fan, high & low temp, voltage, above set temperature (with alarm)Weight100 grams (3.5 oz)DimensionsLength = 98mm (3.8")Width = 95mm (3.7")Depth = 25mm (1”) Davies, Craig’s revolutionary, Australian-designed EWP® pumps are made from anti-corrosive, lightweight nylon reinforced with fibreglass. Universal fit allows for easy mounting into the bottom radiator hose. Our kits come with easy-to-understand DIY instructions and everything you need for easy installation, including different adaptors to fit various hose sizes and all necessary electrical wiring.The EWP®115 and LCD EWP®/Fan Digital Controller Combo Pack is the most economical way to increase horsepower and save on fuel consumption whilst caring for your engine.The Davies, Craig EWP® header adaptor kit can replace the mechanical water pump completely. (See EWP® Header Adaptors on website) Combined with an LCD EWP®/Fan Digital Controller (Sold separately Part #8002 or EWP® Combo Pack) will manage both the EWP® and Thermatic® fan operation. The Digital Controller will vary the speed of the EWP® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. The Thermatic® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C / 14°F below the set temperature) after engine shut down, eliminating ‘heat soak’ and extending engine life. The EWP® Controller Combo Pack is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.The world’s most advanced total engine cooling management system: universal fit more power more cooling increase fuel efficiency extend engine life world-leading technology EWP® INSTALLATION OPTIONSInstalling an EWP® as an AUXILIARY PUMPLeaving the mechanical water pump in place, install the EWP® into the bottom radiator hose.Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.EWP® INSTALLATION – disabling Mechanical water pumpLeaving the mechanical water pump in place, install the EWP® into the bottom radiator hose and remove the manufacturer’s thermostat.You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.In both these cases, the EWP® will pump past the impeller of the mechanical water pump.Disengaged mechanical water pump (recommended)Remove the mechanical water pump and remove the thermostat.Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.Install the EWPÒ into the bottom radiator hose.Removed mechanical water pump (Ideal)Remove the mechanical water pump and thermostat from the engine.Install a Davies Craig EWP® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.Install the EWP® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.Install an appropriate length belt (not supplied) to drive the accessories.In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP®115, EWP®140 and EWP®150 Part #8700 or #8710 Mounting bracket is recommended. PRODUCT SELECTION GUIDEElectric Water Pump (EWP®) APPLICATION PUMP MODELPUMP ONLYPUMP KITPUMP COMBO12V24V12V24V12V24V Engines up to 2.0L(Standard)EWP®80#8105 Nylon#8106 Flange#8109 BarbN/A#8005 Nylon#8006 Flange#8009 BarbN/A#8907 Nylon#8908 Flange#8919 BarbN/A Engines up to 2.0L - 3.5L(Standard)EWP®115#8125 Nylon#8140 Alloy#8126 Nylon#8141 Alloy#8025 Nylon#8040 AlloyN/A#8930 Nylon#8950 AlloyN/A Engines up to 3.5L - 5.0L(Standard)EWP®140#8180 Alloy#8181 Alloy#8080 AlloyN/A#8990 AlloyN/AEngines 5.0L or greater (Standard)Modified Engines Supercharged/Turbo,Drag Racing, 4WD,Off Road, Drifting & SpeedwayEWP®150#8160 Sliver#8165 Black #8161 Silver#8060 Silver#8065 Black#8061 Silver#8970 Silver#8975 Black#8971 SilverIntercooler(depending on capacity)EWP®115#8125 Nylon#8140 Alloy#8126 Nylon#8141 Alloy#8025 Nylon#8040 AlloyN/A#8930 Nylon#8950 AlloyN/AEWP®140#8180 Alloy#8181 Alloy#8080 AlloyN/A#8990 AlloyN/AEWP®150#8160 Sliver#8165 Black #8161 Silver#8060 Silver#8065 Black#8061 Silver#8970 Silver#8975 Black#8971 Silver International buyers – please note: Import duties, taxes, and charges aren’t included in the item price or postage cost. These charges are the buyer's responsibility.

Price: 344.63 AUD

Location: Melbourne, Victoria

End Time: 2025-01-02T23:28:24.000Z

Shipping Cost: 52.97 AUD

Product Images

Electric Water Pump - EWP115 (NYLON) Combo (12V) (Davies Craig) (Part #8930) Electric Water Pump - EWP115 (NYLON) Combo (12V) (Davies Craig) (Part #8930) Electric Water Pump - EWP115 (NYLON) Combo (12V) (Davies Craig) (Part #8930) Electric Water Pump - EWP115 (NYLON) Combo (12V) (Davies Craig) (Part #8930)

Item Specifics

Return shipping will be paid by: Buyer

Returns Accepted: Returns Accepted

Item must be returned within: 7 Days

Manufacturer Part Number: 8930

Brand: Davies Craig Pty Ltd

Manufacturer Warranty: 3 Years

Recommended

Electric Water Pump - EWP115 (ALLOY) Kit (Part #8040) (Davies Craig)
Electric Water Pump - EWP115 (ALLOY) Kit (Part #8040) (Davies Craig)

$155.36

View Details
Sensor - Coolant Temperature (1/4" NPT) (Part #18415)
Sensor - Coolant Temperature (1/4" NPT) (Part #18415)

$11.67

View Details
Temperature Sensor Wire Extension - 1m (Part #10470)
Temperature Sensor Wire Extension - 1m (Part #10470)

$5.46

View Details
Tempreature Sensor 38mm Adapter Kit (Part #0408) For Fan or EWP
Tempreature Sensor 38mm Adapter Kit (Part #0408) For Fan or EWP

$21.72

View Details
DIGITAL THERMATIC FAN SWITCH 1/4" NPT Sensor & Inline Adapter (Part 0445 + 0409)
DIGITAL THERMATIC FAN SWITCH 1/4" NPT Sensor & Inline Adapter (Part 0445 + 0409)

$75.98

View Details
Male Flare Adapter 16AN to 1" NPT (PART #1129)
Male Flare Adapter 16AN to 1" NPT (PART #1129)

$10.59

View Details
Electric Water Pump - EWP80 (NYLON) Kit (Part #8005) (Davies Craig)
Electric Water Pump - EWP80 (NYLON) Kit (Part #8005) (Davies Craig)

$125.77

View Details
EWP Header-Adaptor Ford Windsor (Early) (Part #8640) (Davies Craig)
EWP Header-Adaptor Ford Windsor (Early) (Part #8640) (Davies Craig)

$65.11

View Details
FORD COYOTE EWP BLOCK ADAPTER (Part #8660) (Davies Craig)
FORD COYOTE EWP BLOCK ADAPTER (Part #8660) (Davies Craig)

$98.17

View Details
Electric Water Pump - EWP115 (ALLOY) (Part #8140) (Davies Craig)
Electric Water Pump - EWP115 (ALLOY) (Part #8140) (Davies Craig)

$113.45

View Details