Description: See our video on our high efficiency water heating elements and run video on our new LifePo 4 Bettery DC Water Heater Element 12 Volt 60 Watt w/Bulkhead Adapter Solar Water Heating DC Water Heater Element 12 Volt 60 Watt w/Bulkhead Adapter Solar Water Heating Bulkhead Specifications: 1" Heavy Duty Polypropylene Tank Fittings 2-1/4" Hole Size Specifications:PolypropyleneEPDM gasketsDouble thread (both ends)Meets FDA standards This bulkhead fitting is ideal for DC water heater elements. Double thread (both ends) EPDM gaskets. To install fittings, the indicated hole size must be drilled into tank. Tank fittings for installing water heater elements, tubing connectors, spigots, valves, etc. in tanks. Cut hole size in tank wall, insert fitting thread on and tighten nut. FDA compliant material. Water Heater Element Specifications: ONE 7 INCH DC WATER HEATING ELEMENT 12 VOLT 60 WATT Fits standard water heaters with a 1" NPT First we start with solid brass base and copper Then it gets nickel plated for long life. USESLivestock water tank deicer (low amp draw means you won't drain your battery as fast)For keeping dog, cat, and other domestic animals water from freezing Standard American water heater element replacementWater preheating Campers, Motor homesEmergency hot water Portable commercial, industrial machines and equipment Runs off your car battery for portable hot water anywhereDirect wind and solar applications Concrete mixing trucks and many, many more uses where heat or diversion loads are neededDC water heating elements are much safer than 110 volt WIND TURBINE WATER HEATING Heat water directly using a wind turbine generator (with or without a battery bank). Wind turbine generators are used primarily for electricity generation. The power used can be stored in a battery bank or connected to the mains supply using a suitable grid tie inverter. In very strong winds, and/or when the batteries are fully charged a wind turbine may generate more current than the batteries can handle. Therefore a dump load is often used to divert the extra energy to heat water so it is not wasted and so that the wind turbine does not spin so quickly that it is damaged. Diversion Load Water Heating Typical 12V water heating element which can be screwed into an immersion heater drain-cock hole. When used as a diversion (dump) load, such an element is connected to the batteries via a charge regulator. When the regulator detects that the batteries are fully charged, it diverts the generated electricity to the element which heats water. Hurricane Wind Power 2019Corporate America Today2019 Best Off-Grid Renewable Energy Product Supplier - USAUP TO 50% DISCOUNTSTOP BRANDSPaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. See our other itemsThank you for visiting our Ebay store!DC Water Heater Element 12 Volt 60 Watt w/Bulkhead Adapter Solar Water Heating Bulkhead Specifications: 1" Heavy Duty Polypropylene Tank Fittings 2-1/4" Hole Size Specifications: ---Polypropylene ---EPDM gaskets ---Double thread (both ends) ---Meets FDA standards This bulkhead fitting is ideal for DC water heater elements. Double thread (both ends) EPDM gaskets. To install fittings, the indicated hole size must be drilled into tank. Tank fittings for installing water heater elements, tubing connectors, spigots, valves, etc. in tanks. Cut hole size in tank wall, insert fitting thread on and tighten nut. FDA compliant material. Water Heater Element Specifications: ONE 7 INCH DC WATER HEATING ELEMENT 12 VOLT 60 WATT Fits standard water heaters with a 1" NPT First we start with solid brass base and copper Then it gets nickel plated for long life. USES
Livestock water tank deicer (low amp draw means you won't drain your battery as fast)For keeping dog, cat, and other domestic animals water from freezing Standard American water heater element replacementWater preheating Campers, Motor homesEmergency hot water Portable commercial, industrial machines and equipment Runs off your car battery for portable hot water anywhereDirect wind and solar applications Concrete mixing trucks and many, many more uses where heat or diversion loads are neededDC water heating elements are much safer than 110 volt WIND TURBINE WATER HEATING Heat water directly using a wind turbine generator (with or without a battery bank). Wind turbine generators are used primarily for electricity generation. The power used can be stored in a battery bank or connected to the mains supply using a suitable grid tie inverter. In very strong winds, and/or when the batteries are fully charged a wind turbine may generate more current than the batteries can handle. Therefore a dump load is often used to divert the extra energy to heat water so it is not wasted and so that the wind turbine does not spin so quickly that it is damaged. Diversion Load Water Heating Typical 12V water heating element which can be screwed into an immersion heater drain-cock hole. When used as a diversion (dump) load, such an element is connected to the batteries via a charge regulator. When the regulator detects that the batteries are fully charged, it diverts the generated electricity to the element which heats water. DC Water Heater Element 12 Volt 60 Watt w/Bulkhead Adapter Solar Water HeatingSee our video on our high efficiency water heating elements and run video on our new LifePo 4 Bettery DC Water Heater Element 12 Volt 60 Watt w/Bulkhead Adapter Solar Water Heating Bulkhead Specifications: 1" Heavy Duty Polypropylene Tank Fittings 2-1/4" Hole Size Specifications:PolypropyleneEPDM gasketsDouble thread (both ends)Meets FDA standards This bulkhead fitting is ideal for DC water heater elements. Double thread (both ends) EPDM gaskets. To install fittings, the indicated hole size must be drilled into tank. Tank fittings for installing water heater elements, tubing connectors, spigots, valves, etc. in tanks. Cut hole size in tank wall, insert fitting thread on and tighten nut. FDA compliant material. Water Heater Element Specifications: ONE 7 INCH DC WATER HEATING ELEMENT 12 VOLT 60 WATT Fits standard water heaters with a 1" NPT First we start with solid brass base and copper Then it gets nickel plated for long life. USESLivestock water tank deicer (low amp draw means you won't drain your battery as fast)For keeping dog, cat, and other domestic animals water from freezing Standard American water heater element replacementWater preheating Campers, Motor homesEmergency hot water Portable commercial, industrial machines and equipment Runs off your car battery for portable hot water anywhereDirect wind and solar applications Concrete mixing trucks and many, many more uses where heat or diversion loads are neededDC water heating elements are much safer than 110 volt WIND TURBINE WATER HEATING Heat water directly using a wind turbine generator (with or without a battery bank). Wind turbine generators are used primarily for electricity generation. The power used can be stored in a battery bank or connected to the mains supply using a suitable grid tie inverter. In very strong winds, and/or when the batteries are fully charged a wind turbine may generate more current than the batteries can handle. Therefore a dump load is often used to divert the extra energy to heat water so it is not wasted and so that the wind turbine does not spin so quickly that it is damaged. Diversion Load Water Heating Typical 12V water heating element which can be screwed into an immersion heater drain-cock hole. When used as a diversion (dump) load, such an element is connected to the batteries via a charge regulator. When the regulator detects that the batteries are fully charged, it diverts the generated electricity to the element which heats water. Hurricane Wind Power 2019Corporate America Today2019 Best Off-Grid Renewable Energy Product Supplier - USAUP TO 50% DISCOUNTSTOP BRANDSPayment We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Shipping We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.Returns If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. See our other itemsThank you for visiting our Ebay store! DC Water Heater Element 12 Volt 60 Watt w/Bulkhead Adapter Solar Water Heating Bulkhead Specifications: 1" Heavy Duty Polypropylene Tank Fittings 2-1/4" Hole Size Specifications:PolypropyleneEPDM gasketsDouble thread (both ends)Meets FDA standards This bulkhead fitting is ideal for DC water heater elements. Double thread (both ends) EPDM gaskets. To install fittings, the indicated hole size must be drilled into tank. Tank fittings for installing water heater elements, tubing connectors, spigots, valves, etc. in tanks. Cut hole size in tank wall, insert fitting thread on and tighten nut. FDA compliant material. Water Heater Element Specifications: ONE 7 INCH DC WATER HEATING ELEMENT 12 VOLT 60 WATT Fits standard water heaters with a 1" NPT First we start with solid brass base and copper Then it gets nickel plated for long life. USESLivestock water tank deicer (low amp draw means you won't drain your battery as fast)For keeping dog, cat, and other domestic animals water from freezing Standard American water heater element replacementWater preheating Campers, Motor homesEmergency hot water Portable commercial, industrial machines and equipment Runs off your car battery for portable hot water anywhereDirect wind and solar applications Concrete mixing trucks and many, many more uses where heat or diversion loads are neededDC water heating elements are much safer than 110 volt WIND TURBINE WATER HEATING Heat water directly using a wind turbine generator (with or without a battery bank). Wind turbine generators are used primarily for electricity generation. The power used can be stored in a battery bank or connected to the mains supply using a suitable grid tie inverter. In very strong winds, and/or when the batteries are fully charged a wind turbine may generate more current than the batteries can handle. Therefore a dump load is often used to divert the extra energy to heat water so it is not wasted and so that the wind turbine does not spin so quickly that it is damaged. Diversion Load Water Heating Typical 12V water heating element which can be screwed into an immersion heater drain-cock hole. When used as a diversion (dump) load, such an element is connected to the batteries via a charge regulator. When the regulator detects that the batteries are fully charged, it diverts the generated electricity to the element which heats water.
Price: 42.29 USD
Location: Roanoke, Virginia
End Time: 2024-08-16T21:56:17.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Seller
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Model: 1260BULKHEAD
MPN: 1260BULKHEAD
Brand: Hurricane Wind Power
Voltage: 12 V
