Crown ITech 6000 Power Amplifier (Benched Tested

Description: Crown I-Tech 6000: Bench Tested and works great. Features: Compact, reliable and ultra powerful amp Stereo @ 8 ohms: 1500 watts Stereo @ 4 ohms: 3000 watts Stereo @ 2 ohms: 2500 watts Bridged mono @ 8 ohms: 6000 watts Bridged mono @ 4 ohms: 5000 watts Frequency response (at 1 watt, 20Hz - 20kHz): ?0.25dB Signal to noise ratio below rated 8 ohm power, A-weighted: >105 dB Total harmonic distortion (THD) at full rated power: < 0.35% Damping factor (20Hz - 100Hz): > 5000 Common mode rejection (CMR) (20Hz - 1kHz): > 50 dB Input impedance (nominal): 10 kilohms balanced, 5 kilohms unbalanced Maximum input level: 15dBu or 22 dBu, depending on input sensitivity Latency (analog, digital inputs): 1.05 mS analog, 2.29 mS digital (44.1kHz) A/D, D/A converters: 24-bit, 96kHz Cirrus Logic Digital input: AES/EBU, 16-24-bit, 32-48kHz. Onboard sample rate converter Optional CobraNet input coming soon Network: Onboard TCP/IQ, compatible with standard 100MB ethernet hardware DSP: 24-bit conversion with 32-bit, floating-point DSP processing. Bypass mode available. Has 64 assignable filters with 9 different filter types. Includes all-pass filters, over 2 seconds of delay available per channel, and dual uncorrelated-noise and sine-wave generators Load supervision: Monitors the average impedance on the output of the amplifier. Attenuators: Speed sensitive, continuously variable rotary encoder, 0.5 dB steps, range 0 to ?100 dB Load impedance: stereo: 1/2/4/8/16 ohms; bridge mono: 2/4/8 ohms Voltage gain (referenced to 8 ohm rated output): Adjustable in 0.1V steps from 1.4V to 7.5V (39.3 dB gain to 24.7 dB gain) Required AC mains: Universal AC input, 100-240 VAC, 50/60 Hz (?15%) Maximum AC mains voltage: 277 VAC AC line connector: five cordsets supplied with amplifier (USA, UK, Europe, Australia, India) Front panel controls and indicators: bridge mode, ready, signal, clip, thermal, fault, data, power, AC mains present Glowing blue screen and controls: these let the user adjust the amplifier's attenuation and muting, configure the amp, set up error monitoring (such as temperature and load supervision) and recall DSP presets. The presets allow the user to quickly reconfigure the amp for various applications. LCD control screen: integrated LCD with white LED backlight, controls amplifier setup and operation Attenuator: controls amplifier attenuators in 0.5 dB steps Main menu (amplifier setup): bridge, input Y, recall preset, LCD contrast, input sensitivity Advanced menu: attenuator limit, attenuator link, clip limiter, output voltage limiter, output power limiter, pink noise generator, monitor, input, max input, power-up options Power Cord Connector: Standard 20 amp IEC inlet Switch/circuit breaker: resets the circuit breaker that protects the power supply Output connectors: 2 Speakon, 2 binding posts, 2 male XLR passive analog loop through, XLR active/re-clocked AES/EBU digital loop through Analog input connectors: 3-pin female XLR connector for each channel Digital input connector: 3-pin female XLR connector that accepts a digital signal in the AES/EBU format Ethernet connector: accepts an RJ45 connector for IQ TCP/IQ networking and optional CobraNet transport from a standard network cable. Built into the connector is a yellow LINK ACT indicator that shows network activity, and a green 100MB indicator that shows a 100MB network connection Cooling: dual-zone, microprocessor controlled, continuously variable speed, front-to-back airflow Front Panel: Cast aluminum with integrated handles. Included accessories: rear rack ears with integral EZ-Rack pin, cable retention bar, rack screws, operation manual, power cords, foam air filter Size: 19"w x 3.5"h x 16.2"d. Wt. 28 lbs.

Price: 1050 USD

Location: Derby, Kansas

End Time: 2024-11-28T20:15:34.000Z

Shipping Cost: N/A USD