6V Mini-Generator For 2 Cycle Pull Start Bike Engines

Description: Super Dynamo Lighting Bicycles and Motorized Bikes...Avoid Accidents...Avoid Tickets...Get Lights! Motorized Bicycle Lighting 6 Volt Mini-Generator 12 Volt Mini-Generator Max 6 Volt Mini-Generator With Switch 12 Volt Mini-Generator With Switch 6 Volt Mini-Gen for Pull Start Engines 12 Volt Mini-Gen Max for Pull Start Engines Complete 6 Volt Lighting System LS-1 Complete 7.2 Volt Lighting System LS-2 Complete 12 Volt Lighting System LS-3 Enclosed Light Switch SPST Enclosed Light Switch SPDT Encased 6 Volt SLA Battery Encased 7.2 Volts AA Battery Pack Encased 14.4 Volts AA Battery Pack 6 Volt Mini-Charger For LS-1 and LS-2 12 Volt Mini-Charger for LS-3 Magneto Coil Mini Charger Magneto Coil Lighting System Heavy Duty Headlight Bracket Heavy Duty Tail Light Bracket 6V Mini-Generator For 2 Cycle Pull Start Bike Engines Now you can get a reliable lighting system for your 2 cycle motorized bicycle by using this Mini-Generator designed for 6 volt lighting systems. This particular Mini-Gen item is designed especially for pull start 2 cycle motorized bike engines. Like our regular 6 volt Mini-Gen, this will provide a self sufficient and dependable lighting system. The Mini-Generator is a small electrical unit designed to be mounted inside the engine's magneto case to produce electricity to the Mini-Charger which charges the batteries, or it can be used to produce lighting (up to 5 watts recommended) directly . This "Mini-Gen" is designed to produce AC voltage of 6 or more (nominal) for regular 6 volt 3 watt lighting that's normally used with bicycle dynamo. Just install into magneto case using the 2 rear magneto screws and route red (output) wire through wire harness. The red wire from the Mini Generator will send electricity to your lights through a light switch or connected directly for continuous light. This Pull Start Mini-Gen is easily installed and includes installation instructions and precautions. Just remove the engine magneto cover, then remove the pull starter cog and use the 2 rear screws to attach Mini-Generator inside engine magneto case. Remove wire grommet at the front (white plastic or black rubber) then insert Mini-Gen wire into grommet. Use a pick or small screwdriver or nail to push into the area where wire will fit, then insert wire. This will produce over 6 volts AC at about 900 RPM or driving speeds of about 12 to 15 MPH. Volts can reach up to 12 or more @ 1.2 amps or more during high speeds. If running lights directly from Mini-Gen, avoid revving engine with lights on to avoid blowing out lights. High speeds while driving is O.K. Remove wire grommet at the front (white plastic or black rubber) then insert Mini-Gen wire into grommet. Use a pick or small screwdriver or nail to push into the area where wire will fit, then insert wire. Just temporarily install nut and turn the pull starter cog to make sure there is no rubbing on the Mini-Gen. Instructions and precautions are included for Mini-Gen installation. This will produce over 6 volts AC at about 900 RPM or driving speeds of about 12 to 15 MPH. Volts can reach up to 12 or more @ 1.2 amps or more during high speeds. If running lights directly from Mini-Gen, avoid revving engine with lights on to avoid blowing out lights. High speeds while driving is O.K. After the Mini-Generator is installed, the power wire should be routed toward bicycle seat post for Mini-Charger connection, unless it's being used for other purpose. Wire inside engine case should be positioned away from moving parts and also make sure it will not be pinched under the cover. Use duct tape (any color) or cable ties to secure wire onto bike's bottom bracket and seat post. The Mini-Gen in this photo is connected to the red wire coming from the Mini-Charger. Your results will look far better than this one. NOTE: For pull starter 2 cycle engines, run engine for about 10 seconds then remove cover and check to make sure there's no sign of pull starter cog rubbing on Mini-Gen. PAYMENTS Payments for auction items are expected within 3 days, but no later than 7 days. All payments accepted through Paypal or CIP. Serious inquiries about payment for individual items welcome. SHIPPING Flat rate shipping & handling price is available for the continental USA. Shipping & handling might also be the same for other states outside the continental United States. This item will normally ship within 2 business days, but could take up to 5 business days. To check shipping and handling fees to your state just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page. Items will be shipped to the address provided for transaction. Request to change shipping address after item is shipped will be ignored. We reserve the right to refuse shipment to uncomfirmed addresses in which case buyer will be refunded. INTERNATIONAL shipment is available with slightly higher fees. To check shipping and handling fees to your country just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page. WARRANTY & RETURNS The SUPER DYNO Lighting System (patent pending) is warrantied for 7 days cash back, and 30 days replacement. If you are unsatisfied for any reason, just return the complete kit, and a refund will be issued (less shipping and handling). Shipping & handling is not refundable, and the customer is responsible for shipping cost of the returned item.If any problems are experienced with our products, please contact us for assistance before resorting to any other course of action. NOTE- Any item showing signs of tampering or abuse will void warranty! INTERNATIONAL customers are legible for the 30 days parts replacement warranty ONLY. Customer is responsible for shipping returned items. DISCLAIMER This "SUPER DYNO Lighting System", and all parts, pieces, ideas and designs associated therewith, are the proprietary rights and ownership of Wonderful Creations Store. Any copying, modifying, tampering and or false claims are discouraged and expressly prohibited. By purchasing this system you agree to abide by any and all traffic laws governing your city, state or country and further agree to hold Wonderful Creations and any associates thereof, blameless for any accidents, mishaps, property loss, damages, death, injuries or expenses reportedly, or supposedly caused by the use, or misuse of this lighting system. Copyright © 2004-2010 Wonderful Creations . All rights reserved.

Price: 26.95 USD

Location: Hollywood, Florida

End Time: 2024-10-15T08:30:53.000Z

Shipping Cost: 4.95 USD