4000W 100A MPPT Solar PV Regulators USB 12V 24V 36V 48V Solar Charge Controller#

Description: Features： - LCD Liquid Crystal Display: Large LCD display, support battery working status display, solar panel working status display, mode control display, load output status and each parameter display, normal and fault status display. - 7 Operation Modes：Charging mode, light control mode, light control + time delay control mode, general control mode, manual control mode, timing control mode and test mode, the test mode is only for factory test use. - 4 kinds of voltages automatic identification：It will automatic identify DC12V/24V, DC36V, DC48V by itself. - Large-section Wiring Port: use large-section, large-spacing wiring ports, can be installed 16mm wire, the wire spacing of 7mm increases the insulation performance and the reliability of installation, effectively reduces current and voltage drop while reducing losses. - Dual USB Charging Ports: The solar charge controller adopts a dual USB charging port design, which can charge two devices at the same time, and supports most of USB port devices, such as mobile phones, tablets, PSP game consoles, etc. - Thickened Aluminum Alloy Heat Sink: The MOS tube is used to lock the heat sink design, the heat dissipation is more uniform, and there is no fear of the temperature rise caused by the MOS tube, the powerful heat dissipation capacity can operate normally in the environment of 55 ℃, at the same time, it is equipped with functions to prevent overcharge, overvoltage, DC output low voltage, high voltage protection and reverse polarity protection, etc. Specification: Maximum charging current: 100A 80A 60A Maximum input voltage of photovoltaic panels: 15V-23V(12V), 30V-45V(24V), 45V-69V(36V), 60V-90V(48V) Maximum input power of photovoltaic panels: 1000W (12V), 2000W (24V), 3000W (36V), 4000W (48V) Output voltage: DC12V/24V/36V/48V; DC5V/1.5Ax2USB Support Battery: Lithium Battery & Lead Acid Battery Working temperature: -25℃~55℃ Cooling method: heat sink self-cooling Charging method: Focused MPPT modulation charging Working mode: seven Protection function: prevent overcharge, overvoltage/DC output low voltage, high voltage protection, reverse polarity protection, etc. Note: 1.Please connect the battery to the controller first, and then the photovoltaic panel to ensure that the battery voltage is higher than (12V battery is higher than 10V; 24V battery is higher than 20V; 36V battery is higher than 30V; 48V battery is higher than 40V), otherwise it will cause voltage Identification error. Package Included: 1 x Solar Charge Controller 1 x Manual 10A PWM Solar Charge Controller： Specifications: 100% brand new and high quality. Rated Voltage: 12V 24V Auto Application: Solar System Controller Current: 10A Size: 150*78*35mm With Timer and light sensor,it could work for solar light system. Only For off-Grid PV Solar System. For 10A 12V Pv System: 120W Solar Panel,12V Lead-acid Battery,21V for Max input Voltage For 10A 24V Pv System: 240W Solar Panel,24V Lead-acid Battery,42V for Max input Voltage Safety Instructions: 1.Make sure your battery has enough voltage for the controller to recognize the battery type before first installation. 2.The battery cable should be as short as possible to minimize loss. 3.The regulator is only suitable for lead acid batteries: OPEN,AGM, GEL it is not suited for nickel metal hydride, lithium ions or other batteries. 4.The charge regulator is only suitable for regulating solar modules. Never connect another charging source to the charge regulator. Features: 1.Build-in industrial micro controller. 2.One-key setting,digital display,auto memory function. 3.Fully 4-stage PWM charge management. 4.Build-in short-circuit protections,open-circuit protections,reverse protections,over-load protections 5.Dual mosfet Reverse current protections ,low heat productions. System Connection: 1.Connect the battery to the charge regulator - plus and minus.it will show 1 ,if it detects 12V battery, 2 if it detects 24V battery. 2.Connect the photovoltaic module to the regulator - plus and minus. 3. Connect the consumer to the charge regulator - plus and minus. The reverse order applies when deinstalling! An improper sequence order can damage the controller! Note: Please allow 0-2mm error due to manual measurement. pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! PaymentDelivery detailsAbout TaxesAbout usContact usPaymentPayment is managed by eBay.We will ship to your eBay address. Please make sure your address setting is correct before checkout.Delivery detailsWORLDWIDE SHIPPING. (Except some countries and APO/FPO)Orders processed timely after the payment verification.The images shown are not the actual item and are for your reference only.SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season.About TaxesFor all orders, please note that:Taxes and charges are not included in the item price or shipping charges.Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. About usWe are committed to provide excellent service for all buyers.Welcome to our eBay store:)Contact usOur Working Time (Beijing): 9:00 am ~ 6:00 pm (Monday~Friday)If the item is defective or taking longer than usual to reach you, please do not leave us negative feedback. Send us a message through eBay and we will resolve the issue promptly. Thanks for your support and understanding! If you have any questions, please contact us via ebay mail, we will reply you on the working day in China. And there will be no reply as we are out of office during weekend, we will reply on Monday. Because the time zone between the seller and the buyer is different, please be patient and wait for your understanding. We will be happy to serve you.

Price: 13.15 USD

Location: Shenzhen

End Time: 2024-08-17T21:44:15.000Z

Shipping Cost: 0 USD